Power Substation
Site selection considerations for the future power substation
At this stage, a footprint of the future power substation should be developed, including the layout of the major equipment. A decision on the final location of the facility can now… Read more
Jul 30, 2014 | By Edvard Csanyi
Power Substation
Satellite communication for remote control and monitoring of substations
Substation Automation is a supervisory management and control system that lies in between transmission and distribution systems. The interests on substation automation have been increasing rapidly due to its numerous… Read more
Jul 28, 2014 | By Edvard Csanyi
Cables
What engineers should know about using conduits in power substation designs
There are several locations where conduit is used in power substation designs. The most common one considered is conduit used to provide cable access to equipment, such as breakers, transformers,… Read more
Jul 25, 2014 | By Edvard Csanyi
High Voltage
An Example of Choosing 138 kV Line Circuit Breaker
To better understand a process of high voltage equipment selection, let’s discuss an example of choosing 138 kV Line #3 Circuit Breaker, shown in Figure 1, assuming that the following… Read more
Jul 23, 2014 | By Edvard Csanyi
Testing and Commissioning
Testing of Power Transformer – Measurement of Zero-Sequence Impedance
The zero-sequence impedance is usually measured for all star-connected windings of the transformer. The measurement is carried out by supplying a current of rated frequency between the parallell connected phase… Read more
Jul 21, 2014 | By Edvard Csanyi
Low Voltage
10 Important Precautions When Working On Low Voltage Energized Equipment
For most work, the electrical equipment must be de-energized because there is a high risk of injury to workers if they work on energized equipment. It may be possible to schedule such… Read more
Jul 18, 2014 | By Edvard Csanyi
Energy and Power
How to get rid off the harmonics in electrical system?
The subject of harmonics is also a contributory factor in electrical noise I already wrote few days ago (Cable spacing as a means of noise mitigation). It also causes several other… Read more
Jul 16, 2014 | By Edvard Csanyi
Electric Motor
13 features and advances of using electronic soft starters for a motor starting
Soft starters serve for a continuous adjustment of the starting characteristic of three-phase asynchronous motors to the requirements of the load by controlling the voltage across the motor and enable… Read more
Jul 14, 2014 | By Edvard Csanyi
Cables
Cable spacing as a means of noise mitigation
In situations where there are a large number of cables varying in voltage and current levels, the IEEE 518-1982 standard has developed a useful set of tables indicating separation distances… Read more
Jul 11, 2014 | By Edvard Csanyi
Medium Voltage
Microprocessor and conventional secondary systems compared
Secondary systems are all those facilities needed to ensure reliable operation of the primary system, e.g. a high voltage substation. They cover the functions of controlling, interlocking, signalling and monitoring,… Read more
Jul 09, 2014 | By Edvard Csanyi
Energy and Power
Harmonic distortion and high frequency applications
The presence of harmonic frequencies in addition to the fundamental 50Hz, bring about distortion of the fundamental sine wave. Considerable problems may arise dependant upon the level of this distortion…. Read more
Jul 07, 2014 | By Edvard Csanyi
Energy and Power
How the Weather Affects Conductors
Notice how a conductor is strung between poles. It is not pulled tight; it sags. In hot weather it sags even more than in cold weather. Consider the analogy of… Read more
Jul 04, 2014 | By Edvard Csanyi
Protection
Protection Against Overexcitation Of a Transformer
Overexcitation of a transformer means that the magnetic flux in the core is increased above the normal design level. This will cause an increase of the magnetizing current and the… Read more
Jul 02, 2014 | By Edvard Csanyi
