Edvard Csanyi
1754 awesome technical articles
Hi, I'm an electrical engineer, programmer and founder of EEP - Electrical Engineering Portal. I worked twelve years at Schneider Electric in the position of technical support for low- and medium-voltage projects and the design of busbar trunking systems.
I'm highly specialized in the design of LV/MV switchgear and low-voltage, high-power busbar trunking (<6300A) in substations, commercial buildings and industry facilities. I'm also a professional in AutoCAD programming.
Biography: https://electrical-engineering-portal.com/edvard-csanyi
Energy and Power
Impulse withstand voltage test performed on assemblies
Only optional in the past, the impulse test which allow defining the rated impulse withstand voltage Uimp, is now a necessity thus demonstrating the strategy of the Standards directed to increasing the importance of such performance. In addition to the… Read more
Mar 02, 2015 | By Edvard Csanyi
Energy and Power
6 recommended practices for increasing the power quality
Power quality concerns have traditionally focused on harmonics, which are generated by nonlinear loads, although there are many other concerns regarding isolating sensitive loads from transient disturbances, uneven ground potentials, or phase imbalances. Poor power quality affects the reliable operation of computers and… Read more
Feb 27, 2015 | By Edvard Csanyi
Cables
4 practical approaches to minimize voltage drop problems
The NEC states in an Informational Note that a maximum voltage drop of 3% for branch circuit conductors, and 5% for feeder and branch circuit conductors together, will provide reasonable efficiency of operation for general use circuits. For sensitive electronic… Read more
Feb 25, 2015 | By Edvard Csanyi
Testing and Commissioning
Do Not Energize Oil-Filled Transformer Without Performing These 15 Tests and Checks!
The following tests and checks should be performed at a minimum to ensure that the transformer is ready to be energized. Do not energize the transformer without performing these tests and checks. If any of below explained tests fail and… Read more
Feb 23, 2015 | By Edvard Csanyi
Testing and Commissioning
Basic Transformer Routine Test – Measurement of Winding Resistances
The resistance between all pairs of phase terminals of each transformer winding are measured using direct current. Furthermore the corresponding winding temperature is measured. The measured resistances are needed in connection with the load loss measurement when the load losses… Read more
Feb 20, 2015 | By Edvard Csanyi
Energy and Power
Smart Load Management Strategies To Save Energy
As part of their drive towards synchronizing the consumption and production of electrical energy over the long term, energy distribution companies tailor their rates to encourage consumers to reduce their requirements during peak periods. A number of different strategies are… Read more
Feb 18, 2015 | By Edvard Csanyi
High Voltage
Selection of high voltage conductors and earth wires
Conductors represent the most important component of an overhead power line because they have to ensure economical and reliable transmission and contribute considerably to the total line costs. For many years, aluminum and its alloys have been the prevailing conducting… Read more
Feb 16, 2015 | By Edvard Csanyi
Energy and Power
How can I select the right capacitors for my specific application needs?
Once you’ve decided that your facility can benefit from power factor correction, you’ll need to choose the optimum type, size, and number of capacitors for your plant. There are two basic types of capacitor installations: individual capacitors on linear or… Read more
Feb 13, 2015 | By Edvard Csanyi
Energy and Power
Ring Main Unit (RMU) as an important part of secondary distribution substations
Before getting into “What is RMU” question, let’s say a word about the distribution system where RMU is often used. Distribution systems encompass power lines that transport energy from the transmission network or other sources to consumers, along with the… Read more
Feb 11, 2015 | By Edvard Csanyi
Energy and Power
A real life analogy of the jurisdiction of the protection relay
Formally, a relay is a logical element which processes the inputs (mostly voltages and currents) from the system/apparatus and issues a trip decision if a fault within the protection relay‘s jurisdiction is detected. A conceptual diagram of relay is shown… Read more
Feb 09, 2015 | By Edvard Csanyi
Datacenters
Emergency Lighting Power Supply in Data Center
Lighting is defined as emergency lighting when it is intended for operation when standard lighting fails. Emergency lighting must be powered by an independent energy source (typically a central power supply system) and is classified by the UNI EN 1838 standard… Read more
Feb 06, 2015 | By Edvard Csanyi
Energy and Power
Voltage Imbalance Protection of Synchronous Generator (ANSI Code 60)
In an apparatus protection perspective, generators constitute a special class of power network equipment because faults are very rare, but can be highly destructive and therefore very costly when they occur. If for most utilities, generation integrity must be preserved… Read more
Feb 04, 2015 | By Edvard Csanyi
Energy and Power
Calculating Max. Demand Kilovolt-Amperes and Required Cable Current Rating
A building site is to have the following electrical equipment available for use: Tower crane, electric motors totalling 75 kW at 415 V; Sump pump, 5 kW at 240 V; 60 tungsten lamps of 100 W each at 240 V;… Read more
Feb 02, 2015 | By Edvard Csanyi
Energy and Power
Important generator set (genset) rating considerations
A generator set (genset) consists of an engine and a generator and it is best to consider each of them as a system. Individually, each has unique characteristics, but together these qualities have a significant impact on the performance and sizing of the genset… Read more
Jan 30, 2015 | By Edvard Csanyi
Energy and Power
4 Essential Features of Transformer On-Load Tap Changer (OLTC)
On-load tap changers (or circuit tap changers), as the name suggests, permit tap changing and hence voltage regulation with the transformer on-load. Tap changing is usually done on the HV winding for two reasons: Because the currents are lower, the… Read more
Jan 28, 2015 | By Edvard Csanyi
