Search

Premium Membership ♕

Limited Time Offer: Save 15% on PRO Plan with discount code: LRN15 and study specialized LV/MV/HV technical articles and studies.

Home / Download Center / Electrical Engineering Books and Technical Guides / Electrical engineering guides / Lightning protection in a nutshell (design, bonding, earthing and testing – IEC 62305)

Power distribution systems with RCDs

Within a power distribution system, overcurrent and residual current devices (RCDs) are used for the protection of human lives against shock hazard as well as to protect the structure / equipment and occupants from fire and other hazards that could result from an electrical fault.

Lightning protection in a nutshell (design, bonding, earthing and testing)
Lightning protection in a nutshell (design, bonding, earthing and testing)

Similarly, surge protection devices are installed to also reduce these risks due to lightning currents. It is important that the installation of surge protection devices does not compromise the operation of overcurrent and residual current devices.

Where conflicts exist, priority should be given to the overcurrent and residual current devices. Often in the case of RCDs, this resolution requires the installation of the surge protection devices to be installed in a less favorable position.

Residual current devices (RCDs) may also be known as residual current circuit breakers (RCCBs) or earth leakage circuit breakers (ELCBs).

The three main issues with RCDs are:

Issue #1 – Large lightning current passing through the RCD could cause damage to the RCD, thereby inhibiting its operating and causing a safety hazard.

Issue #2 – Nuisance tripping when surge protection devices installed downstream operate (the current flow to ground can be detected as a potentially life threatening leakage current.

Issue #3Nuisance tripping when large lighting currents are passed through the RCDs. Due to small imbalances in the detection circuit, when large lightning currents are passed and returned via the RCD the RCD may incorrectly detect an imbalance.

Generally it is desirable to install SPDs prior to RCDs to avoid situation 1. However, some local codes may not permit SPDs to be installed prior to RCDs. It is important to follow the local code requirement with regard to installation and selection of RCDs.

Installation of SPD into typical low current single phase panel with no additional back-up overcurrent protection
Installation of SPD into typical low current single phase panel with no additional back-up overcurrent protection

In other countries, RCDs are only used on branch circuits feeding to wet areas such as bathrooms, hence SPDs can be installed prior to RCDs.

Type “S” or “selective” RCDs are specially designed to have a higher immunity to lightning impulses (to 3 kA 8/20 µs). Internal filtering desensitizes the detection circuits to harmonics, inrush currents and lightning currents.

There is generally little concern with class III tested SPDs being installed downstream of RCDs.

In fact class III tested SPDs are often only installed L-N to protect against differential mode voltages, thus further reducing the risk of interaction with the RCD.

Title:Lightning protection in a nutshell (design, bonding, earthing and testing) – nVent/ERICO
Format:PDF
Size:16.1 MB
Pages:92
Download:Right here | Video Courses | Membership | Download Updates
Lightning protection in a nutshell (design, bonding, earthing and testing)
Lightning protection in a nutshell (design, bonding, earthing and testing)

Premium Membership

Get access to premium HV/MV/LV technical articles, advanced electrical engineering guides, papers, and much more! It will help you to shape up your technical skills in your everyday life as an electrical engineer.
50% Discount 💥 - Save 50% on all 90+ video courses with Enterprise Membership plan.

More Information

4 Comments


  1. I need to fo this area my thesis plz can i get the file
    Jul 30, 2022

    I am electrical engineer . I am intrest on this


  2. TAY ZAR WIN
    Jan 29, 2019

    Very useful and attractive material to study for the advance of my profession. Thanks for your sharing knowledge and data. Best Wishes,


  3. Andrei
    Jan 28, 2019

    In your practice do you usually installed SPD in a main panel or in a separate special box?


    • Edvard
      Jan 28, 2019

      I prefer more installation in the same panel. Connections are shorter.

Leave a Reply to Andrei

Tell us what you're thinking. We care about your opinion! Please keep in mind that comments are moderated and rel="nofollow" is in use. So, please do not use a spammy keyword or a domain as your name, or it will be deleted. Let's have a professional and meaningful conversation instead. Thanks for dropping by!

fifteen  ⁄    =  three

Learn How to Design Power Systems

Learn to design LV/MV/HV power systems through professional video courses. Lifetime access. Enjoy learning!

Subscribe to Weekly Newsletter

Subscribe to our Weekly Digest newsletter and receive free updates on new technical articles, video courses and guides (PDF).
EEP Academy Courses - A hand crafted cutting-edge electrical engineering knowledge