Search

Premium Membership ♕

Limited Time Offer: Save 15% on PRO Plan with discount code: LRN15 and study specialized LV/MV/HV technical articles and studies.

Home / Download Center / Electrical Engineering Books and Technical Guides / Electrical engineering guides / Learn selectivity and coordination in LV systems (fuses & circuit breakers curves)

Selectivity example

If the emergency overcurrent protective devices are not selectively coordinated with the normal path overcurrent protective devices (OCPD), a fault in the emergency system can cause the OCPDs to cascade open thereby unnecessarily opening the normal path feeder OCPD or possibly main OCPD.

Learn selectivity and coordination in LV systems (fuses & circuit breakers curves)
Learn selectivity and coordination in LV systems (fuses & circuit breakers curves)

Figure 1 illustrates this scenario. If this occurs, all the vital loads are unnecessarily without power at least temporarily. Since the power is lost to the ATS normal lineside termination, the generator is signaled to start.

When the generator starts and the loads transfer to the alternate source, some vital loads will continue to be unnecessarily blacked out due to the emergency feeder OCPD’s lack of selective coordination (it is still open).

In addition, this action reduces the reliability of the system since there is some probability that the generator may not start or the transfer switch may not transfer.

Example of Non-Coordinated System
Figure 1 – Example of Non-Coordinated System

Evaluate for the Worst Case Fault Current

In assessing whether the overcurrent protective devices are selectively coordinated in the circuit path for these vital loads, it is important that the available short-circuit current from the normal source be considered (see Figure 2).

Generally, the normal source can deliver much more short-circuit current than the emergency generators. This is required per 700.5(A) Capacity and Rating.

The emergency system equipment shall be suitable for the maximum available fault current at its terminals.

Example of Coordinated System
Figure 2 – Example of Coordinated System

Full Range of Overcurrents

To comply, the overcurrent protective devices must selectively coordinate for the full range of overcurrents possible for the application: overloads and short-circuits which include ground faults, arcing faults and bolted faults.

IMPORTANT NOTE – It is not selective coordination if the fuses or circuit breakers are coordinated only for overloads and low level fault currents. The fuses or circuit breakers must also be selectively coordinated for the maximum short-circuit current available at each point of application.

High- and medium-level faults may not occur as frequently as overloads and very low-level faults, but they can and do occur. High- and medium-level faults will be more likely during fires, attacks on buildings, building failures or as systems age, or if proper maintenance is not regularly performed.

Selective coordination has a very clear and unambiguous definition. Either overcurrent protective devices in a circuit path are selectively coordinated for the full range of overcurrents for the application or they are not.

The words “optimized selective coordination,” “selectively coordinated for times greater than 0.1 second,” or other similar wording are merely attempts to not meet the selective coordination requirements.

And terms like “selective coordination where practicable” are unenforceable.

Title:Selectivity and coordination in LV systems (fuses and circuit breakers curves) – Cooper Bussmann
Format:PDF
Size:2.1 MB
Pages:50
Download:Right here | Video Courses | Membership | Download Updates
Learn selectivity and coordination in LV systems (fuses & circuit breakers curves)
Learn selectivity and coordination in LV systems (fuses & circuit breakers curves)

Premium Membership

Get access to premium HV/MV/LV technical articles, advanced electrical engineering guides, papers, and much more! It will help you to shape up your technical skills in your everyday life as an electrical engineer.
50% Discount 💥 - Save 50% on all 90+ video courses with Enterprise Membership plan.

More Information

One Comment


  1. Akhila
    May 30, 2019

    It’s too easy understand but I need basic concept

Leave a Reply to Akhila

Tell us what you're thinking. We care about your opinion! Please keep in mind that comments are moderated and rel="nofollow" is in use. So, please do not use a spammy keyword or a domain as your name, or it will be deleted. Let's have a professional and meaningful conversation instead. Thanks for dropping by!

  −  3  =  one

Learn How to Design Power Systems

Learn to design LV/MV/HV power systems through professional video courses. Lifetime access. Enjoy learning!

Subscribe to Weekly Newsletter

Subscribe to our Weekly Digest newsletter and receive free updates on new technical articles, video courses and guides (PDF).
EEP Academy Courses - A hand crafted cutting-edge electrical engineering knowledge